ASTM D4066 PDF

Buy ASTM D CLASSIFICATION SYSTEM FOR NYLON INJECTION AND EXTRUSION MATERIALS (PA) from SAI Global. ASTM D Standard Classification System for Nylon Injection and Extrusion Materials (PA). standard by ASTM International, 07/01/ View all product. 暂无评价|0人阅读|0次下载 | 举报文档. D – 01A Nylon Injection and Extrusion Materials_能源/化工_工程科技_专业资料。ASTM D标准.

Author: Vudor Jusida
Country: Nepal
Language: English (Spanish)
Genre: Science
Published (Last): 18 June 2005
Pages: 434
PDF File Size: 8.69 Mb
ePub File Size: 11.64 Mb
ISBN: 190-7-44662-888-7
Downloads: 72830
Price: Free* [*Free Regsitration Required]
Uploader: Kemi

Maximum moisture content of specimens shall be 0. Active view current version of standard. No descriptions are listed unless needed to describe a special grade under the class.

Flexural modulus d066 be determined on Test Methods D test specimens 6. Relative viscosity of Group 08 shall be measured on 9. Five specimens shall be tested.

It is not intended for the selection of materials. The designation PAG35 indicates the following: Relative viscosities of Groups 03 and 04 shall be measured on 0.

Historical Version s – view previous versions of standard. D — 96a: These shall be agreed upon between the user and s4066 supplier, by using the suffixes as given in Section 5. Material selection should be made asym those having expertise in the plastic field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this classification system.

  BLUM BLUM SHUB GENERATOR PDF

ASTM D – 96 Standard Classification System for Nylon Injection and Extrusion Materials (PA)

D ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. It is not intended for the selection of materials.

Refer to Table X3. Some of these compositions are also suitable for compression molding and application from solution. The electrodes shall be inserted after the specimens have been conditioned. Viscosities for Groups 03, 04, 06, and 08 are measured as described as follows. R Tensile strength and elongation shall be determined on Test Method D test specimens 3.

A AM — 01a All All tests shall be conducted on as-molded not annealed specimens conditioned dry-as-molded. This standard does not purport to address all of the safety concerns, if any, associated with its use.

Material selection should be made by those having expertise in the plastic? Plastic and Ebonite ISO To be agreed upon between the user and the supplier.

G Relative Viscosities for Group 03 were generated from a correlation with Test Method Dutilizing an Ubbelohde viscometer, and m-Cresol as the solvent. It is the responsibility of the user of this standard to establish appropriate safety and health practices aztm determine the applicability of regulatory limitations prior to use. It is the responsibility of the user of this standard to establish appropriate d466 and health practices and determine the applicability of regulatory limitations prior to use.

These specimens shall be tested. Link to Active This link will always route to the current Active version of the standard.

  IEC 60296 PDF

Industrial & Engineering Plastics

Users of this standard are expressly advised that determination of asrm validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

L Izod impact requirements for Group 04 materials based on specimens with a These will be spelled out in detail and identi? NOTE 12—An example of a special material using this classi? There may be other requirements necessary to identify particular characteristics important to specialized applications.

There may be other requirements necessary to identify particular characteristics important to specialized applications.

D – 01A Nylon Injection and Extrusion Materials_百度文库

D — 00a: Material data for inje NOTE 6—Materials containing reinforcements or? If necessary, additional control of these reinforcements and additives can be accomplished by use of the suffix part of the system see Section 5.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Start the test within 2 min after removing the specimen and wiping with a dry cloth. Weatherable nylon typically contains 1. The lot-acceptance inspection shall consist of the tests listed as they apply: It satm recommended that the material manufacturer be consulted on all call-outs against this classification system.

Author: admin