BC458 DATASHEET PDF

BC Datasheet, BC PDF, BC Data sheet, BC manual, BC pdf, BC, datenblatt, Electronics BC, alldatasheet, free, datasheet, Datasheets, . ABSOLUTE MAXIMUM RATINGS. PARAMETER. SYMBOL. VALUE. UNIT. Collector-Base Voltage. VCBO. V. Collector-Emitter Voltage. VCEO. V. 2SC Transistor Datasheet pdf, 2SC Equivalent. Parameters and Characteristics.

Author: Masida Mele
Country: Norway
Language: English (Spanish)
Genre: Health and Food
Published (Last): 7 March 2008
Pages: 310
PDF File Size: 3.70 Mb
ePub File Size: 18.23 Mb
ISBN: 493-9-50070-885-3
Downloads: 59137
Price: Free* [*Free Regsitration Required]
Uploader: Malasar

For amplification applications, the transistor is biased such that it is partly on for all input conditions. Anything more than 5mA will kill the Transistor; hence a resistor is always added in series with base pin to limit the current. Of the above types common emitter type is the popular and mostly used configuration.

BC is general purpose silicon, NPN, bipolar junction transistor. When this transistor is fully biased, datasheft can allow a maximum of mA to flow across the collector and emitter. BC is used in common emitter configuration for amplifiers. Arduino based GPS receiver. As mentioned the biasing current should be maximum of 5mA.

BC is a NPN transistor so the collector and emitter will be left open Reverse biased when the base pin is held at ground and will be closed Forward biased when a signal is provided to base pin. To bias a transistor we have to supply current to base pin, this current I B daatsheet be limited to 5mA.

  LUDLUL BEL NEMEQI PDF

It is used for amplification and switching purposes. What is Web Browser. The variants of BC are A, B and C which vary in range of current gain and other characteristics.

The maximum DC current gain is When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above.

The transistor terminals require a fixed DC voltage to operate in the desired region of its characteristic curves. The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor.

Skip to main content. When used as an Amplifier the DC current gain of the Transistor can be calculated by using the below formulae.

As discussed a transistor will act as an Open switch during Forward Bias and as a closed switch during Reverse Bias, this biasing can be achieved by supplying the required amount of current to the base pin. Its equivalent transistors are 2N and 2SC Choosing Motor For Robots. It can amplify power, voltage and current at different configurations.

2SC458 Datasheet, Equivalent, Cross Reference Search

The value of I B should not exceed 5mA. This is known as the biasing. For switching applications, transistor is biased so that it remains fully on if there is a signal at its base. These equivalent transistors however have different lead assignments.

  ADAM SI EVA LIVIU REBREANU PDF

Transistor BC548

The datasheett of this resistor R B can be calculated using below formula. SPI Module of Arduino. The voltage divider is the commonly used biasing mode. Amplifier modules like Audio amplifiers, signal Amplifier etc. Interface SD Card with Arduino.

The current gain may vary between and A Transistors acts as an Amplifier when operating in Active Region. Choosing Battery for Robots.

Transistor B C datasheet & applicatoin notes – Datasheet Archive

Interface GPS with Arduino. The input signal at base is amplified and taken at the emitter. Virgin Galactic — Commercial Space Flight. Complete Technical Details can be found at the BC transistor datasheet give at the end of this page.

This high-density System-in-Package SiP integrates controller, power switches, and support components. When base current is removed the transistor becomes fully off, this stage is called as datashfet Cut-off Region and the Base Emitter voltage could be around mV.

BC has a gain value of tothis value determines the amplification capacity of the transistor. In the absence of base signal, it gets completely off.

TL — Programmable Reference Voltage. Submitted by admin on 16 March

Author: admin