FOR ZEROING AT 25 METERS, ROTATE THE REAR SIGHT ELEVATION KNOB TO THE METER (6/3) SETTING. (DO NOT USE THE “Z” MARK ON THE. DOD-M4 25 Meter Zeroing Target M-4 Carbine Official Military Target /4″ X 11″ Tag Target Paper Box of M4 Carbine. M16A4. M16A2. For every yards of range from the target, one (1 ) click will move the strike of the bullet on the target approximately: OBJECTIVE.

Author: Ducage Garr
Country: Zambia
Language: English (Spanish)
Genre: Spiritual
Published (Last): 21 October 2012
Pages: 17
PDF File Size: 4.50 Mb
ePub File Size: 19.43 Mb
ISBN: 278-4-51471-369-7
Downloads: 72182
Price: Free* [*Free Regsitration Required]
Uploader: Gashicage

Home Safety Targets Contact. Or, is the real target a different size? This is a “mechanical zero” and should never reay be adjusted its much more efficient to implement Kentucky windage for closer targets.

Will this sight be capable of doing so? At 25m the round has not yet moved the through trajectory to strike the target center mass of m, so you account for it with the rear sight adjustment and that’s why you have to move it back at completion. Should i print it on 8×11, 8×14 or 11×17? M4 Carbine – 25 Meter Zeroing Target.

These instructions are for iron sights only as the point of impact POI for optical sights will vary. Started up to date web throw best free apps for tablet download game android mobogenie download asphalt 5 for android app downloader free android wallpapers themes free download http: Zero target data for the M4 Tatget Web Hosting by iPage.

If you were conducting the zero at meters vzo wouldn’t do that step. This target is the real deal!

Use the meter zero target for the M4 Carbine and center your rounds by adjusting the weapon front sight post garget the BUIS windage adjustment knob. When using the meter mark too zero at 25 meters will the sights be on target at meters? Is that the actual size?? The Recoil Screw has a locking patch on the threads so it must be replaced if removed. Kevin O’Day on December 15, See if you can hit what you’re aiming at!


Could not find this target anywhere in San Angelo, Texas. We use this targey for patrol rifle class and for sighting department weapons.

It’s usually differences in fundamentals applied among individual shooters that cause the variations in a zero for the same rifle. I think the “one click past” is considered the mechanical zero?

I’ve seen these offered on 8. Sarge 40 on August 25, We use this target to train new recruits on sighting AR platform patrol rifles.

Even at the gun stores where they sell AR15 and M4 weapons. Adjust the sights to move the shot group center as close as possible to the white dot in the center of the target.

Site Search Categories All. Sarge40 on August 25, Excellent target. I’m late on answering this. To zero M16A4 Rifle, turn the knob until the line on the sight cam on the left side is aligned with the white line between the and marks. This mark is a half notch location, so it’s more difficult to align.

M4 Carbine – 25 Meter Zeroing Target

The extra click is definitely for mechanical zero. Do not over tighten. Targdt on August 16, I’m late on answering this. Anyway, while I can get my hands on the Army zero sheets I wanted to see what was available on line.


Target – M4 Carbine – 25 Meter Zeroing Target | Print Free Targets

That seems to be a bit small for a 25 meter target. This sheet was pretty accurate. I can’t believe this is available! The sight radius on an M16A2 is The BUIS must be mounted in the rearmost slot on the upper receiver for the range adjustments and the zeroing procedures to be correct.

M16A2 and M4 meter zero target. It is funny though because Army and Marine vary slightly. When standard zeroing procedures are followed, a properly bzk weapon for one person is close to the zero for another person for that specific rifle. Zeroed hundreds of weapons.

What if your department requires zeroing at yards? The front sight post should be flush. Hi fashionable work http: Pancho on January 12, I think there might be an error in the first, and third step of your instructions.

This target is also commonly used to zero AR pattern rifles. Reply Your comment will be posted after it is approved. Instead set your rear sight to the horizontal line under the m setting on your BUIS. I think there might be an error in the first, and third step of your instructions.

Make sure the BUIS is flat on the receiver rail with the angled edge under the upper receiver rail. What is the optimal distance between front and back sight?

Author: admin